회원가입/수정 MY Page 장바구니 주문조회
 
 
비밀번호 확인 닫기
전동자동차 > 1/8 전동트러기 > ASSOCIATED > [AAK80948] RC8T4e Team Kit 조립품 전문가용 -(베터리,충전기미포함)
전동자동차
[AAK80948] RC8T4e Team Kit 조립품 전문가용 -(베터리,충전기미포함)
제조회사 : TEAM ASSOCIATED
판매가격 : 945,000원
적립금액 : 9,450원
총 상품 금액 0
     
   
상품 상세 설명
 






RC8T4e Team Kit Features


Four battery configurations to choose from:

Two 2s shorty "saddle pack" LiPo batteries for lowest CG and exceptional weight bias

Two 2s full size "saddle pack" LiPo batteries for using capacity batteries

One 4s shorty LiPo battery for simplified setup and more centralized weight bias

One 4s full size LiPo battery for simplified setup and ability to use your existing batteries

Innovative front-end geometry with reduced kingpin inclination steering blocks places the wheel pivot in the center of the front tire for increased stability and consistent steering through the entire steering throw

Paired with a new wider upper suspension arm pivot


New gearboxes are specific to front and rear:

Front gearbox features a 3.5deg. inclined pinion gear angle to straighten the center driveshaft for increased drivetrain efficiency and reduced phasing and vibration

Rear gearbox features a 0deg. pinion gear angle and center mounted rear chassis brace mount

Both gearboxes feature larger bearing sizes over RC8B3. Switching to a 6x13x5mm flanged bearing (from a 6x12x4mm non-flanged) results in longer life of bearings and ring and pinion gears

Reduced hardware on anti-roll bar cap for easy assembly and maintenance

Increased strength in common areas of part fatigue; particularly around the pinion gear and outer cap bearing fitment


Updated front upper suspension arm design

An added molded hinge pin bushing to reduce slop and increase suspension dynamics


New rear wing mount has adjustable wing angle shims, significant strength improvements, an aerodynamic shape, and extra clearance for shock position adjustment

Two wing height options are available to tune the rear downforce

Three wing angle positions: 0, -2, and -4 deg.

The improved design also secures the wing mounting nuts so that they will not spin in the mount

The four wing mount screws into the rear tower access from the rear end of the buggy for simplified maintenance


New rear wing has more vertical fins for increased straight-line stability, a taller rear wickerbill height for increased downforce, increased strength in various areas to reduce bending fatigue, and dimples on the backside as a template for cutout holes

Two wing buttons are included for additional tuning options: the first is a traditional one-piece flat button and the second is a vertical stabilizing fin for even more straight-line stability


New rear chassis brace has several design features and flex options:

Rear brace is mounted centrally to the gearbox, which reduces material fatigue, centralizes shear forces, and improves the life of rear end drivetrain parts

Has three different chassis flex options using two chassis hole mounting locations

Use both screws (most rigid)

Use one screw, long location

Use one screw, short location (most flexible)

The upper brace joint has two flex tuning options at the gearbox

With included molded inserts that prevent twisting and only allow flex along the centerline pivot of the brace

With optional turnbuckle ball for flex in more degrees of freedom

Removable insert to customize the amount of flex in the brace


New +1mm offset rear hub features a symmetrical left and right common design with axle height inserts for adjustable roll center tuning

The standard bearing size used is an 8x16x5mm flanged but the hub will still accept 15x21x4mm bearing for CVA axle tuning options

New two-piece clamping motor mounts make for secure mounting and allows for mounting of a 30 mm motor fan

The gear mesh is adjusted from the bottom of the chassis, just like RC8T4

New +2 mm taller front shock tower design with updated suspension geometry and body mount positions for all styles of truck bodies

Run a single centered body post mount for "bruggy" type bodies

Run two offset body post mounts for traditional "truggy" type bodies

Run an included top plate mounted body post for bodies utilizing "buggy" front end mounting points


New longer shock shafts and shock rod ends

35.5mm front and 44.5 mm rear shock shafts

0 mm, +2 mm, and +4 mm shock rod ends are included for tuning droop and up-travel for various shock positions


Other New Features


New steering bellcranks with top-mounted steering rack for extra clearance around gearbox assembly


New aluminum steering rack designed around the updated front end geometry is lightweight and durable


New steering bellcrank nuts are longer to reduce drag from the steering rack under flex


Updated steering servo linkage features a new heavy duty threaded ball and steel screw joint


New A and B blue aluminum suspension arm mounts are shaped to interlock with the RC8B4 chassis


New RC8T4e specific 7075 aluminum hard anodized chassis features updates to strengthen the front and rear droop tab areas and an increased width along kick up area


New upper suspension arm link mount is significantly wider than RC8B3 series, providing the required geometry for the new reduced KPI steering blocks


New front chassis brace is the same length as the "short" version from RC8B3 for ideal front end flex


New spring cups and shock rod end design has a locking screw to keep the cups in place during a crash and has improved material; the same tough material as our 1:10 rod ends


New front shock bushings are 1.5mm longer than RC8B3 shock mounts


New rear shock bushings are 4mm longer than RC8B3 shock mounts

Large diameter, Low-Profile SHCS are used throughout the truck to replace a traditional screw/washer system


New exhaust hanger mount and spring


New carbon fiber radio tray brace for repositioned steering servo


New 152mm rear center and RC8B4e 104 mm dog bones (used on the front) with 14mm pins on are now standard equipment for increased drivetrain efficiency


New rod ends have improved thread engagement, slotted area for easy turnbuckle wrench access, and are made from a same durable material as our 1:10 rod ends


New CVA axle has a "stub" design with retainer sleeve to capture pin and uses two 8x16x5mm flanged bearings (the same as the 

RC8B3 universal axle setup)


New 131 mm CVA bones used on all four corners


New rear shock tower features two built in wing height positions; the RC8T4e "low" is the same height as the RC8T3 "high" and RC8T4 features an additional +5mm height option by adjusting the wing mount adapters, all easily accessed from the rear end of the truck


Standard anti-roll bar sizes include a 2.2mm front and 2.4mm rear bar


Standard shock spring setup includes a yellow 5.7 lb/in rate front and red 4.7 lb/in rate rear spring


RC8T4e TEAM Legacy Features:

+2deg. steering block arms

V3 differentials with 46T ring and 10T pinion gears for improved gear ratios

Includes new updates to HTC sun and planet gears with removed pocketing to extend diff life and improve gear mesh and remain more consistent over long runs

RC8B3.2 side guards that thread into the chassis from the top side of the car

RC8B3.2 split center diff mounts with aluminum center top plate

RC8B3.2 shock caps with stiff molded bladders

RC8B3.2 narrow C and D arm mounts

No body is included with RC8T4e kit. Racers can use AE #81324 RC8T3 body or choose from a variety of current bodies from aftermarket companies.

 
1. 구입금액이 50,000원 이상일 경우 무료배송이 적용되며, 50,000원 미만일 경우 배송비를 고객님께서 부담 하셔야 합니다.
2. KGB택배 배송료 : 2,500원(제주,도서/산간지역은 추가 배송료가 적용됩니다.)
3. 평일(월~금) 오후 4시 및 토요일 오후 12시까지 입금확인이 되는 주문은 당일 발송해 드립니다.
4. 배송기간은 입금확인일로부터 평일기준 1~2일 소요됩니다. (도서/산간지역은 배송이 지연 될수도 있습니다.)
1. 고객님께서 취소하신 상품에 대한 환불은 현금의 경우 반품 확인 후 고객님이 요청하신 통장으로 입금하여 드립니다.
2. 신용카드로 결제하신 경우 신용카드의 거래승인을 취소하여 드립니다.
3. 반품을 하시는 경우 구입하신 상품과 행사제품을 함께 보내시거나, 행사제품에 대해 해당되는 일정금액을 부담하셔야 합니다.
1. 상품수령 후 7일 이내에 반품및 A/S가능
2. 제품의 하자 및 주문내역과 다른 상품이 배송된 경우 반품 및 교환 배송요금은 판매자가 부담.
3. 고객 변심으로 인한 반품 및 교환시에는 배송비를 부담하셔야 합니다
상품 성격상 사용 여부의 확인이 불가능한 제품은 교환 및 환불이 불가능합니다.
4. 조립 제품으로 조립을 시작한 경우나 밀폐된 포장을 개봉한 경우,또는 상품 가치가 상실된 경우에는 상품불량 이라도 반품 및 교환이 불가하니 조립 또는 개봉전 반드시 확인 하시기 바랍니다.
1. 상품의 불량에 의한 반품, 교환, A/S, 환불, 품질보증 및 피해보상 등에 관한 사항은 소비자분쟁해결기준(공정거래위원회 고시)에 따라 받으실 수 있습니다.
2. 대금 환불 및 환불 지연에 따른 배상금 지급 조건, 절차 등은 전자상거래 등에서의 소비자 보호에 관한 법률에 따라 처리합니다.
 
 
 
상품 사용 후기
 
이름 : 첨부 : 파일첨부
내용 :
평점
 
 
 
 
상품 QNA
 
상품에 대해 궁금한 점을 해결해 드립니다.
번호 제목 작성자 작성일 조회
 
 
회사소개     |     장바구니     |     주문조회     |     MYPAGE     |     자료실     |     이용약관     |     개인정보 보호정책     |     이용안내